eufy Genuine Pole Mount Bracket (T870C) | Brand New
$45.00
Skip to product information
eufy Genuine Pole Mount Bracket (T870C)
Condition Brand New
$45.00
Know before you buy
The quick decision check
- Condition
- Brand New
- Stock
- Available now
- Delivery · Australia Post
-
Express Post
FREE on $99+ orders
$12.95 below $99
Standard
$9.95 below $99
Order total after discounts.
Delivery estimates & policy
Express Post
Choose compatible extras Choose only what your setup needs
Use the regular Add to cart button for this product on its own. Check the setup requirements above and each extra's listing for included parts and firmware requirements.
This adds the product shown above and every selected extra in one step. Use the regular Add to cart button for the product on its own.
Choose your viewThe essentials or the full story. Switch any time.
eufy Pole Mount Bracket · T870C
Strapped on. Pole stays whole.
-
Fits
eufyCam E40 (T8144), 3, 3C, S3 Pro · SoloCam S340, E30, E42 · PoE Cam S4 (T8E00), E40, E41 · 4G LTE models. Not the battery eufyCam S4 (T8172). Look up your camera ›
-
Does
Holds one camera on a vertical pole 50 to 150 mm across. Stainless straps wrap it, so nothing drills into the pole.
-
Condition
Brand New: factory sealed in eufy’s retail pack. The bracket only, no camera or pole.
-
From us
12-month CamGuard warranty · dispatched from Townsville · free Express on $99+ orders after discounts
Pole width: 50 to 150 mm across
Measure the pole first
How wide is your pole?
Tap your pole’s width, straight across
✓50 to 150 mm · in eufy’s range
The two stainless straps wrap it and tighten at their latches. Then check your camera below.
✕Under 50 mm · too thin
eufy rates the straps from 50 mm, so we can’t promise a firm fit.
✕Over 150 mm · too wide
Past eufy’s 150 mm limit for the straps.
✕Square post · not promised
eufy gives a diameter and its guide draws round poles only, so we can’t promise a square post.
No calliper? Wrap a tape measure around the pole. About 16 to 47 cm around is inside eufy’s range (our maths: around ÷ 3.14 = across).
eufy’s hole chart for this bracket
Cameras eufy names.
-
A✓ Fits
eufyCam and 4G LTE Starlight
eufyCam E40, battery T8144 · eufyCam 3 / S330 T8160 · eufyCam 3C / S300 T8161 · eufyCam S3 Pro T8162 · 4G LTE Starlight Camera T8150
-
B✓ Fits
SoloCam and 4G LTE Cam
SoloCam S340 T8170 · SoloCam E30 T8171 · SoloCam E42 T8173 · 4G LTE Cam S330 T86P2
-
C✓ Fits
PoE Bullet-PTZ Cam S4
PoE Bullet-PTZ Cam S4 T8E00. The wired one, not the battery eufyCam S4.
-
D✓ Fits
PoE Cam E40 and E41
PoE Cam E40, bullet T8P00 · PoE Turret Cam E41 T8P10
-
✕✕ Not compatible
Not on eufy’s chart
eufyCam S4, battery T8172: eufy’s own pages disagree and the chart leaves it off, so we mark it not compatible. Also eufyCam 2C and 2C Pro, SoloCam S220 and S230, doorbells, indoor and floodlight cams.
The T-number is on your camera’s label and in the eufy app. Look up your camera ›
Fitting, from eufy’s guide
Thread. Wrap. Tighten.
-
Release the straps
Cut the tie, loosen the screws and pop open each latch.
-
Wrap and tighten
Run the straps through the slots, wrap them tightly round the pole, snap each latch shut, tighten the screw, then the buckle.
-
Camera on
Screw the camera to the holes for its letter with the UP stamp upward. A tail cable threads through the centre hole.
You’ll need: a Phillips screwdriver and gloves (eufy’s guide says to wear them).
Condition and parcel
Boxed, not yet strapped.
Condition
Brand New
Factory sealed in eufy’s retail pack. Never fitted.
In the parcel
1 × eufy Pole Mount Bracket (T870C), the bracket only
Not included
Camera · pole · cable · power
Included fittings
The bracket, standard stainless mounting straps, camera-mounting screws and printed guide are included. A camera is sold separately.
Good to know.
Will it fit my camera?
Yes, if your camera’s T-number is on eufy’s hole chart above (holes A to D). The battery eufyCam S4 (T8172) isn’t on it, so we don’t sell this bracket for that camera.
What size pole does it suit?
A vertical pole 50 to 150 mm across, which is eufy’s range for the straps. eufy’s guide draws round poles only.
Do I drill into the pole?
No. The stainless straps wrap the pole and tighten with a Phillips screwdriver. The camera screws to the plate.
Is it weatherproof?
eufy describes metal with an electrophoretic coating and a white powder finish. It publishes no IP rating, weight or load rating for the bracket, so we don’t quote any.
When will my order leave Townsville?
We do our best to get orders out the same day. Same day to 1 business day is our typical dispatch time from Townsville, Queensland. During busy periods it can take a little longer, though that’s rare. Australia Post delivery time is on top.
Buying from CamGuard Australia
Sent from Townsville.
Shipping
Australia Post Express is included on orders of $99 or more after discounts. Under $99.00 it’s $9.95 tracked, or $12.95 Express.
We aim to dispatch the same day; same day to 1 business day is typical from Townsville, Queensland. During busy periods it can take a little longer, though that’s rare.
Warranty
Our own 12-month warranty, not a manufacturer warranty, with Australian Consumer Law rights on top. Faulty or not as described? We cover the return postage.
Returns
Change of mind within 30 days of delivery, complete and unused. You pay return postage; the original shipping isn’t refunded.
Who you’re buying from: an independent Australian importer and reseller in Townsville, not eufy. Happy to answer questions before you buy.
Tech specs.
Bracket
- Name
- eufy Pole Mount Bracket
- Model
- T870C (retail code T870CA20)
- Made for
- A vertical pole 50 to 150 mm across
- Straps
- Adjustable stainless steel
- Material
- Metal, electrophoretic coating, white powder finish
- Hole sets
- A to D for the cameras on eufy’s chart; E for one eufy accessory model (T8708); F for future models
- Also on the plate
- Centre hole for a tail cable · UP stamp
- Tool needed
- Phillips screwdriver
- Not published by eufy
- IP rating, weight, dimensions, load or wind rating
Parcel
- Condition
- Brand New, factory sealed in eufy’s retail pack
- In the parcel
- The pole mount bracket
- Not included
- Camera, pole, cable, power
- Included fittings
- Straps, camera screws, printed guide
The camera list is eufy’s own hole chart from the bracket’s quick start guide. Where eufy’s documents disagree, we follow the most recent one, and where eufy hasn’t confirmed a camera we mark it not compatible until it does.
The bracket holds a camera. It doesn’t record anything or prevent anything.
The product photo is eufy’s own image. Illustrations and diagrams are labelled.
Our own 12-month warranty applies, not a manufacturer warranty. Nothing here limits your rights under Australian Consumer Law.
CamGuard Australia is an independent importer and reseller, not an official or authorised supplier, distributor or representative of eufy, Anker Innovations or their affiliates. Product names and trademarks belong to their owners.
Details believed accurate at time of listing.
CamGuard Australia · ABN 62 385 894 763 · Townsville, Queensland
GWEG'S SHEDBig jobs · tiny brackets · questionable estimates
By CamGuard Australia
Aisle eventuallyBay: round thingsTrade-ish counterSnag status: pending
Saturday project control · T870C
NO WALL?
HAVE A POLE.
The genuine eufy T870C wraps a compatible camera mount around a round post, pipe or pole, without drilling into the pole itself.
Before Gweg cuts the snag: this is the bracket only. Camera and pole are not included. Measure the pole straight across: it must be round and 50–150 mm in diameter.
Gweg's four-bay shortcut
The useful bits before your second lap of the car park.
Aisle directory that finally helps
Right pole. Right camera. Right hole pattern.
4G LTE4G LTE Starlight Camera and 4G LTE Cam S330.
eufyCamE40, S330 (eufyCam 3), S300 (eufyCam 3C) and S3 Pro. Check eufyCam S4 separately; the named S4 below is the PoE model.
SoloCamS340, E30 and E42.
PoEPoE Cam S4, E40 and E41; eufy also lists the LongRange Station.
Not sure?Send CamGuard the exact model number. “It is the white eufy one” is not a model number, even at Gweg's.
Gweg's Tip Exchange · advice accepted, then repaired
Gweg explains it badly. CamGuard translates.
Gweg's tip 02“Titen it untill the pole gives a tiny appology.”
Actual translationTighten both bands firmly and evenly so the plate does not shift. Do not keep forcing the screw, deform the pole or damage the band mechanism. Recheck the mount before adding the camera.
Gweg's tip 03“Cut the spare band off furst. Less band means less jobb.”
Actual translationPosition, thread, latch and tension the bands before trimming anything. Confirm the final location and leave sensible adjustment room; replacement spare bands are not supplied with this listing.
Gweg's tip 04“The UP arrow is more of a creativ sugeston.”
Actual translationKeep the plate's UP marking upward. If the camera has a tail cable, route it through the centre opening before fastening the camera to the correct hole pattern.
Gweg's tip 06“Cyclone test: stand neer it and say ‘she'll be rite’ with confidance.”
Actual translationeufy does not publish a wind-load, bracket IP or temperature rating here. Assess the pole, exposure and fastening for the site, and use a suitably qualified installer where structural or high-wind suitability matters.
Gweg's yellow notes are the joke. The white translations are the instructions. If the two ever disagree, trust the person who brought the tape measure.
The trade-ish counter
What comes home, and how it goes on.
On the trolley
- Genuine eufy T870C mounting plate
- Adjustable stainless-steel banding
- Camera screws: confirm the supplied size
- eufy quick-start guide
Not included: camera, pole and spare replacement banding.
Saturday installation order
- Measure and confirm a round 50–150 mm pole.
- Confirm the exact camera and its hole pattern.
- Thread the bands through the bracket and around the pole.
- Latch and tighten with a Phillips screwdriver.
- Route any tail cable, keep the UP arrow upward, then attach the camera.
Open Gweg's “do not discover this after cutting” note
The bands are trim-to-fit and eufy does not offer spare replacement bands through this listing. Confirm the position and fit before trimming. Installation suitability still depends on the pole, camera, environment and competent fastening.
Open the condition note
Brand New and factory sealed in genuine eufy retail packaging. This is not renewed, refurbished, open-box or New No Box stock.
Customer copy · print slightly crooked
The honest docket.
Modeleufy Pole Mount Bracket · T870C / T870CA20
DimensionsConfirm bracket dimensions and pole fit before installation
Weather claimsRust-resistant coated metal. No bracket IP, temperature or wind rating is promised here.
DispatchTypically same day to 1 business day from Townsville; busy periods can take longer.
PostageTracked $9.95 or Express upgrade $12.95 under $99. Express included on orders of $99 or more after discounts.
WarrantyCamGuard Australia's own 12-month warranty, not a manufacturer warranty, alongside your Australian Consumer Law rights.
Returns30-day change of mind when unused and complete; buyer pays return postage and original shipping is not refunded. Faulty or misdescribed goods: CamGuard covers return postage.
Shipping, warranty and returns.
Shipping
Australia Post Express included on orders of $99 or more after discounts. Under $99.00: $9.95 tracked or $12.95 Express. We do our best to get orders out the same day; same-day to 1 business day is our typical dispatch time from Townsville, Queensland; during busy periods it can extend, though that is rare.
Warranty
CamGuard Australia is an independent importer and reseller. Our own 12-month warranty applies · not a manufacturer warranty. Faulty or not as described inside that year and we cover the return postage. Your rights under Australian Consumer Law are additional.
Returns
Change of mind: 30 days from delivery, complete and unused, buyer pays return postage, original shipping not refunded. Faulty or not as described: we cover return postage.
Condition on this listing
Brand New. Factory-sealed in full original retail packaging, unopened and unused.
CamGuard Australia
© 2026 CamGuard Australia · ABN 62 385 894 763 · Townsville, QLD. Independent Australian reseller of eufy cameras, doorbells and locks; not an official or authorised supplier of eufy, Anker Innovations or their affiliates. Trademarks belong to their respective owners.
Condition: Brand New. Factory-sealed in full original retail packaging, unopened and unused. We describe packaging and the published spec sheet only and do not open or test each unit individually. Compatibility: Check exact-model compatibility before purchase.
The The Saturday Hardware Counter setting is a fictional presentation of this listing. Product facts and CamGuard terms remain separate from the story. Specifications sourced from the manufacturer and believed accurate at time of listing; features and compatibility may be updated without notice.
Product specifications
- Color
-
- White
- Material
-
- Metal
- Suitable space
-
- Outdoors
Proof from real orders
Customer reviews
Product feedback and verified-buyer experiences collected by Judge.me.